-
Design And Construction Of A Digital Clock With Calendar
-
-
-
Since 170Ω is not available in the market, 220Ω resistor value is selected and use.
Components for frequency stabilization are definitely very useful, but sometimes unnecessary. In most cases the oscillator may operate at frequencies which are not precisely defined so that the installation of such components is a waste of money therefore. The simplest and cheapest solution here is to use one resistor and one capacitor for the oscillator operation.
-
-
-
ABSRACT - [ Total Page(s): 1 ]ABSTRACT This project is aimed at explaining the Design and construction of a digital wall clock with calendar. It give report on how we can achieve this aim and the primary objective of this work is to bring a vibrant digital clock display to everyone located within the vicinity where the clock is being installed, and the importance of clock is to tell time and date, so you can meet up with events and assignments, these are just few importance of CLOCK. In developing countries, time is a ... Continue reading---
APPENDIX A - [ Total Page(s): 3 ]APPENDIXROUTINE PROGRAME THAT HANDLES COUNTINGPROGRAMMING CODE ... Continue reading---
LIST OF TABLES - [ Total Page(s): 1 ]LIST OF TABLE Table TABLE: 2.2.3 CONVERTING DIGITS TO SEVEN SEGMENT DISPLAY BITS TABLE 4.2: VOLTAGE REGULATOR TEST RESULT ... Continue reading---
LIST OF FIGURES - [ Total Page(s): 1 ]LIST OF FIGURESFigure FIG.1.0 THE PIC16F877 INTERNAL STRUCTURE FIG 2.0 BLOCK DIAGRAM OF A DIGITAL CLOCK WITH CALENDAR DISPLAY FIG. 2.2.1 POWER SUPPLY UNIT FIG. 2.2.2 MICROCONTROLLER UNIT FIG2.2.3 SEVEN SEGMENT DISPLAY FIG 2.2.4a MASKING OF SEVEN SEGMENT DISPLAY FIG 2.2.4b SCANNING AND MULTIPLEXING OF SEVEN SEGMENT DISPLAY FIG 3.0 BLOCKS DIAGRAM OF THE STAGES IN DIGITAL CLOCK WITH CALENDAR FIG 3.1 CIRC ... Continue reading---
TABLE OF CONTENTS - [ Total Page(s): 1 ]TABLE OF CONTENT Title Page Certification Dedication Acknowledgement Abstract Table of Contents List of Table List of Figure CHAPTER ONE1.0 INTRODUCTION 1.1 BRIEF DISCUSSION ON CLOCK 1.1 AIM 1.2 OBJECTIVES 1.3 UNITS OF THE SYSTEM 1.3.1 HARDWARE PART 1.3.2 SOFTWARE PART CHAPTER TWO2.0 LITERATURE REVIEW 2.1 HARDWARE COMPONENTS 2.2 STAGES IN ... Continue reading---
CHAPTER ONE - [ Total Page(s): 3 ]ï¶ Counting unit;Each unit of the clock is linked to a general purpose register for counting purposes. There is a routine program that handles counting up for each of the clock units (refer to appendix for codes of routine program). The time taken for each increase is determined in the routine handling it. The output of each counter is binary and therefore needs to be converted to seven segment display format. Another routine is program to handle this (refer to appendix for routine pro ... Continue reading---
CHAPTER TWO - [ Total Page(s): 6 ]CHAPTER TWO3.0 LITERATURE REVIEWThis project is an embedded system that uses a microcontroller to achieve the required functions. This device operates by running a software program burn into its flash memory, this is divided into loops, and each loop has it specific function. These loops are labeled counter, decoder and display scanner.In this project, I have built a digital clock with 24 hour count time. The clock runs from 00:00 to 23:59 and then back to 00:00. The display has two four d ... Continue reading---
CHAPTER FOUR - [ Total Page(s): 3 ]CHAPTER FOUR4.0 THE CONSTRUCTION After proper design and calculations for each stage, the components were obtained and connected together on a breed board and tested to ensure that the circuit connections were okay before it was transferred to the vero-board and soldered. The construction of each unit was carried out stage by stage with proper testing after each completion. The construction started from the power supply unit to the visual display unit and the casing.During soldering, ... Continue reading---
CHAPTER FIVE - [ Total Page(s): 1 ]CHAPTER FIVE5.0 CONCLUSION This digital clock is designed to display real time clock and calendar. There were lots of problems encountered while working on this project. These include generating clock signal of 1sec from 4Mz clock signal of the MCU, Synchronizing the timing along with the scanning of the display simultaneously and writing code fired into the microcontroller. Other problems encountered include choice of components, obtaining and interpreting datasheet of components fo ... Continue reading---
REFRENCES - [ Total Page(s): 1 ]REFERENCESEvans C. H. (2007) Amplifiers (Electronics) New York, van Nestraud Rinold, New York. Hughes E. (2003): Hughes Electrical, 6th Edition. Harlow Longman scientific and technology.Integrated Electronics, M. C. Grewhill book by Robert B. S. Company (2008) Ivo Adanand Jacques Resing, The Queueing theory (2002), Department of Mathematics and Computer science, Eindhoven University of Technology, Eindhoven, The Netherlands.Paul H. & Winfield H (2000). The Art of Electronics, 2nd edition. Cambri ... Continue reading---
-
ABSRACT - [ Total Page(s): 1 ]ABSTRACT This project is aimed at explaining the Design and construction of a digital wall clock with calendar. It give report on how we can achieve this aim and the primary objective of this work is to bring a vibrant digital clock display to everyone located within the vicinity where the clock is being installed, and the importance of clock is to tell time and date, so you can meet up with events and assignments, these are just few importance of CLOCK. In developing countries, time is a ... Continue reading---